Blog

Water Heater Repair Rockford IL Blog

Our blog is designed to give homeowners as much information on general plumbing repair tips, not just Rockford IL water heater repair advice.  Many home plumbing maintenance tasks homeowners can be well equipped  to take care of themselves.  Enjoy!

The Water Heater Temperature Argument

Posted by on Jan 26, 2014 in Water Heater Repair Rockford IL | 0 comments

There are different views on exactly what is the best temperature level at which to set ones water heater. Water Heater Repair Rockford IL will be sharing a few of the various views with particular proof from those sources in order for one to make his/her own decision on the topic.Water Heater Repair Rockford IL

First off, the default setting most water heater manufacturers have their products set at is 140 degrees. If you have actually never examined this already, that may be what it is set at. Likewise, it can be difficult to understand for sure what the temperature setting is since lots of times the temperature dial does not have degrees printed on it, simply warm, hot, really hot … something to that end. Some people feel they are pre-set at a higher temperature so it feels remarkable to have a lot of hot water – kind of like attempting to create excellent brand name awareness in consumers.

In terms of energy savings, by turning a water heater down from 140 to 120 degrees, it will save between 6 to 10 percent of total energy used. That equates to in between $6 to $20 a year in the majority of cases.

Let’s begin with the probably the most renowned source, the U.S. Department of Energy. They recommend a setting of 120 degrees. The link with their website above gives a great deal of good info on the best ways to reduce ones hot water usage and costs. It is for sure worth a read.

Now for the health threats of too low of a temperature setting. It can be concluded that Legionella bacteria has the optimal growth range in between 68 to 122 degrees. Treehugger states that “25 percent of all water heaters have varying levels of Legionella bacteria contamination.”

According to The National Center for Biotechnology Information: “There are two opposing risks when it comes to water temperature inside domestic water heaters; exposure to Legionella, the bacteria responsible for Legionnaires’ disease (pulmonary legionellosis), and the risk of scalding.” (read more…)

Legionella bacteria triggers a form of pneumonia and is passed to humans when one inhales water contaminated with the bacteria – typically in showers, whirlpool baths or even air conditioning systems. Consuming the water is generally ok. It is an issue with having the bacteria get in ones lungs.

The Centers for Disease Control and Prevention estimates 8,000 to 18,000 Americans contract the condition annually. 5 to 30 percent of the cases are fatal.

According to the Occupational Safety & Health Administration, here are some of the factors that can increase the risk of getting the disease:

  • Organ transplants (kidney, heart, etc.)
  • Age (older persons are more likely to get disease)
  • Heavy smoking
  • Weakened immune system (cancer patients, HIV-infected individuals)
  • Underlying medical problem (respiratory disease, diabetes, cancer, renal dialysis, etc.)
  • Certain drug therapies (corticosteroids)
  • Heavy consumption of alcoholic beverages

In Conclusion

So choose if there are any issues of individuals burning themselves if the water temperature level is too hot. Likewise, be aware of any individual who has issues of contracting Legionella Disease. Because the yearly cost savings of turning the temperature down is just about $20 the majority of the time with the average home’s hot water use, it may be a good choice to keep the temperature above 120 degrees simply for the wellness related benefits; nonetheless, Water Heater Repair Rockford IL will let you make the call.

The following two videos reveal how to adjust the temperature on both an electric and a gas water heater in case you are not sure how to do so.

How to Change the Temperature on an Electric Hot Water Heater

How To Change The Temperature On A Gas Water Heater

Read more articles in our blog.

How to Flush a Rockford Water Heater

Posted by on Jan 17, 2014 in Water Heater Repair Rockford IL | 0 comments

Ok, so it is not a glamorous water heater maintenance task, but it does require a little cleaning up from time to time. Yes, today Water Heater Repair Rockford IL is going to instruct one on ways to flush out a water heater. Some suggest doing so once every one to 3 years, we feel it is best to do so once a year. Doing so is not a tough or time consuming project – heck, let the children lend a hand even.

Why Flush a Rockford IL Water Heater?

If it is last the advised life expectancy of the device, it ought to have some sort of routine flushing done. Doing so will clearly aide in having it run as successfully as possible, which likewise implies conserving money on the cost of running the darn thing. That alone should be a sufficient reason we feel!

In regards to water heater maintenance, flushing it will do away with the accumulation of mineral deposits that natural occurs inside the water storage tank. If one has actually ever had loud sounds, popping, gurgling, mini-explosion noises, that is an indicator that there is too much sediment inside the tank. This flushing procedure will assist ensure that the tank heats water far more quietly.

Step 1. If it is an electric water heater, turn the power off in the main electric breaker box and turn the cold water supply off. If it is a gas heater, it is ok to leave the gas on – just turn the water off. Though, turn the thermostat setting dial to the pilot setting (make a note to bear in mind exactly what it was originally set at though for later). Then, whichever faucet the water heater supplies is closest requires to be opened. This is normally simpler than opening the pressure relief valve, but one can do that rather.Water Heater Repair Rockford IL

Step 2. At the bottom of the water heater is a drain valve that a yard watering hose can be connected to. There could be a cover over it depending upon the maker. Think about turning the heat to the pilot setting several hours prior to flushing it if one desires so the water isn’t going to be as hot when it is drained. If that is not an option that’s okay, simply make sure the garden hose utilized is in good condition to endure the greater temperature water.

Run the hose outside away from your home or if the water has cooled, one can drain the tank into buckets.

Step 3. Open the water heater’s drain valve and begin draining the water. For whatever reason the drain valve is usually made from plastic, so if one has an older water heater (and one that has actually not been drained since before time began) it could stick a little. Simply be careful to not break the plastic (which is why it would be nice if the darn thing was NOT made of plastic).Water Heater Repair Rockford

Once the drain valve is open, also open the pressure relief valve on the heater. Water will (at least it must if it pressure relief valve is working effectively) flow some from it. Attempt to let is stream stable and not too fast so it stirs up the sediment in the water heater. We want the sediment to drain out the bottom through the hose.

If draining in a bucket, even if having the hose drain into a bucket outside of the garage or basement where the water heater is located, fill a container and let it sit to see if the water is clear or if there is sediment, which will normally appear like sand in the bottom of the container. Simply keep draining it up until the water is clear.

Step 4. Close the drain on the bottom of the tank and close the pressure relief valve if it is still open.

Step 5. Turn the supply of water on again to fill the tank. Once it is full once more, slowing open the pressure relief valve again to get some excess air out of the tank. Then, open a hot water faucet in the residence to get even more air out of the system.

Step 6. Let the hot water in the bathtub run up until a complete stream is flowing out. When that occurs, it is ok to turn the power back on if it is an electric water heater, or reset the temperature setting for a gas water heater. Obviously, turn the bathtub faucet off. In about 20 minutes, the hot water should be heated again.

There you go! Water Heater Repair Rockford IL is here to address any questions you might have. Next take have a look at our post on what to do if one has no hot water.

Enhanced by Zemanta

Troubleshooting No Hot Water from a Water Heater

Posted by on Jan 15, 2014 in Water Heater Repair Rockford IL | 0 comments

Let us break down the discussion on why one may not have any hot water from the water heater into 2 different parts: having NO hot water and having LIMITED hot water.

No Hot WaterGas Water Heater Repair Rockford

In regards to having no hot water at all, Water Heater Repair Rockford IL recommends that it is probably since of one of the following four various possibilities (at least it is most likely simply one). Below they are …

A Bad Pilot Light
Ideally this is the case due to the fact that it is the most convenient of the 5 to fix. First check to see that it is still lit. One might should have a look at the owners manual (sorry guys, but occasionally we need to check out directions) if you are having a hard time finding where it is found. Manufacturers due have a tendency to hide them nowadays it seems. And, to see what the makers instructions are for relighting the pilot light.

Gas Line Leak
If one has a gas water heater, there might be a leak in the line. If one has an electric one, certainly disregard this as a possibility. Some individuals have a difficult time smelling gas, though my mother has an uncanny ability to smell it I vividly remember as a kid. It most likely will have the smell of rotten eggs. If this is the case, all jokes aside, turn the gas line off if one knows where it is and call the gas company and/or a plumbing business if one does not live in Hot Water Heater Repair Rockford IL’s service area. This is a serious problem that requires instant attention!

A Bad Thermostat
This could be the concern for both not having any hot water, or just not having enough hot water. To be on the safe side we included it in this section though. Make certain the thermostat dial settings have not been bummed or changed by mishap. Our water heater is located in the garage and the happy fingers of twin children like to go checking out once in a while. If the
settings are what they usually are, turn the setting up some and see if it suffices. The thermostat can be changed for they do wearperiodically.

A Bad Thermocouple
For gas water heaters, the thermocouple works in hand with the pilot light as a security device. If the pilot light is out, it avoids gas from being switched on, so it is kind of essential. Nevertheless, easy to alter if needed. When the thermocouple begins to break, it “informs” the gas valve that the pilot light is out so it turns off the gas. The gas burner will not light then and the pilot light goes out.

For electric water heaters, it utilizes a heating element inside to carry out the electrical current heating the water. These can also break and will result in decreased hot water.

Not Enough Hot Water

Sediment Buildup
If one is not in the routine of flushing the water heater tank periodically, like at least once every couple years, sediment from the water will buildup in the bottom of the tank. If one ever hears popping or banging noises from the storage tank, that is probably why. This will ultimately lower the heaters capability to make adequate hot water. Regular flushing will generally resolve this trouble. If the water in your home is extremely hard, making use of a water softener will assist battle an excess amount of sediment accumulation too.

Other Possibilities
There may be a problem with the flame from the burner. Please ensure the location around and underneath the water heater remains clean from dirt. The water heater pulls air up from below for the burner. Natural gas flames will burn bright blue with a yellow tip, while propane are more bluish green on the body of the flame.

It could hold true that the tank size is just too small and unable to deal with the water heating demands, however certainly if it is a brand-new trouble of insufficient hot water and ones usage level has actually not considerably increased, this will not hold true.

If any current repairs were made on the system something might be crossed in regards to the electrical connections or the cold and hot water connects, but once again, quite unlikely from most plumbing companies.

There are various other possible causes, however for the sake of time here, Rockford Water Heater Repair simply wished to share the most probably ones. Do not think twice to let us know of any assistance required!

Video Overview of Water Heater Repair Rockford IL

Posted by on Jan 9, 2014 in Plumbing Repair Rockford IL, Water Heater Repair Rockford IL | 0 comments

We just assembled a brand-new company video summary for Water Heater Repair Rockford IL and we desired to share it with you today. Do not hesitate to call us for any plumbing repairs and setups that you may should have done at work or at home.